Tag Archive: fitting

DIY Fitting uPVC Windows

Installing your own UPVC windows

For those DIY inclined amongst us, fitting your new UPVC windows may seem like a interesting challenge. While it is a mammoth task requiring time and hard graft, it is by no means impossible. It will require preparation, accuracy and pleanty of research to simplify the process sufficiently.

If this is your debut installation, it would be good to start on a small scale. After you have finished your first window, you can move onto something larger. Always take time to make sure you are doing a job right, to avoid paying out later.
The first thing you will need is the correct set of tools. To fit a window you will need:A drillA chiselA screwdriverA spirit levelDoor sealant and frame sealantA sawFrame fixingsAn 8mm drill bit

Before you do anything, check if there is a lintel above the window before you start to remove it. Something to bear in mind is that uPVC windows are not load bearing. Get rid of all items of a breakable nature and anything that could be ruined by any dust. The final step before starting is to check the size of the window matches what you have ordered.

On to the removal of any existing windows. The first parts of the window you should remove are the opening sections Use a screwdriver or nail bar to gently remove them. Start off in the top corner and work your way down, removing from the inside by safely cracking the glass pane. Remove any grout or plaster from the frame with a sharp knife carefully. Use a saw to cut through the uprights at an angle, so it makes it easier to pull apart. But don’t cut all the way through as you may end up damaging the plaster. Using a chisel, lever where the cut is behind the frame, so that you can cut through at the end. Wiggle the frame and pull to cleanly remove it. Repeat the process again to remove the head timber and sill.Clean up the area, removing any dangerous debris and protrusions.

Moving on to the fitting of the new window:If you have decided to install a sill,make sure that the up stand lines up with the plaster line.Level the sill with a 5mm clearance from the brickwork, using the plastic the sill in place with fixing bolts, ensuring that it is level, then apply a sealant at the back edge of the up stand. Finish off with superglue to stick the end caps on.Remove all glazing beads, mark where you have taken them out so that you can put them back in the same position .Slowly place the window into position, between the sill and up stand. Any excess silicone needs to be removed as you go along to avoid a big clean up job up a spirit level and ensure that the window is fully vertical against the silicone line.While taking care not to over-pack or damage the framework, wedge the window in to position using the plastic packers. Using plastic packers, wedge the window into place making sure that you don’t damage the framework. Secure the base with you need to drill it into the brick and insert the frame fixers and the glass in place after inserting glazing bridges in the recess located in the frame.

Place a bead of silicone between the outside masonry and window frame, then between the plaster and the window. Wipe away any excess silicone before removing any protective tape you may have used.Finally, leave the window for a few hours to let the seals set before opening.

Fitting Compression Joints

Select to do a threaded variety or a unique type, but so long that you kind a top quality connection and steer clear of leaks that will want to come.

Security ought to come to mind first, due to the fact actively playing all over with PCV pipe fittings calls for eye protections and a basic safety mask. The explanation why is that when you minimize via the PVC, you need to have to make certain your eyes don’t get any dust in them. Also, it’s effortless to get nasal and eye irritation since of the primer made use of to clear the tubes. This is when you set cement on the pipes that you are about to join. Make convinced to get the job done where there is lots of air flow so you never damage yourself from the chemical substances as they could do serious injury if you are not thorough.
As you can see, employing PVC pipe fittings is not as uncomplicated as you may believe. It can be difficult but then yet again you can constantly retain a single of the a lot of pros to do it for you.

In the previous, plumbing pipes were usually iron or lead. Just about every has its positive aspects and drawbacks – lead, for instance, is effortless to bend but it calls for ability to join, it is highly-priced and lead plumbing methods have been a contributory factor in direction of lead poisoning in delicate h2o parts. Presently, most plumbing pipes are copper, however stainless metal and rigid and adaptable plastics are often utilised. Plastic pipe is getting to be more widespread for the cold water services pipe in new houses.

Copper pipe

Copper pipe is normally effortlessly obtainable and reasonably effortless to operate with. It comes in a variety of dimensions and is sized by its outside diameter – 15mm, 22mm and 28mm are the most widespread sizes. Primary runs and pipes feeding bath taps and the hot h2o cylinder are typically 22mm pipe. Pipes to all other taps are commonly 15mm in diameter. The 28mm size might be employed for some boiler pipes and often for feeding the sizzling drinking water cylinder (rather of 22mm pipe).
Copper pipe can be lower with a fine-toothed hacksaw or with a particular pipe cutting tool. Treatment will need to be taken when applying a hacksaw to minimize the close of the pipe accurately square, and the lower have to be filed easy the two within and out. A pipe cutter tends to go away a burr on the inside of of the pipe – this will need to be filed off or taken out with the pointed reamer on the pipe cutter.

Copper pipe can be bent pretty easily but it need to be supported during the practice or it will kink. Scaled-down diameters can be bent by hand with the aid of a bending spring. This is a stiff steel coil of just about the same diameter as the inside of the pipe. It is pushed into the pipe all-around the position where by the bend is to be created and supports the pipe all through bending. The spring need to be compressed a tiny – by turning it – previous to trying to with&notdraw it. You have to have a single for every single size of copper pipe.